Customers who have used the elevator door pocket praise its decorative effect, which will give people a fashionable and atmospheric effect in the overall decorative effect. However, we will also receive feedback from customers that the installed elevator door pocket has uneven seams and uneven seams. In fact, it is not difficult to present the effect of elevator door pocket, and the technology of installation workers is also very important. Let's analyze three situations that affect the installation effect of elevator door pocket.

一、電梯門套裁切的尺寸有誤差，可能會出現一些缺陷。

1、 There is error in the cutting dimension of elevator door pocket, and some defects may appear.

二、安裝電梯門套前沒有做墻面好找平的工作，導致安裝后就會出現有縫隙的情況。

2、 The wall surface was not leveled before the installation of elevator door pocket, resulting in cracks after installation.

三、安裝工人并不是木工師傅，不會切割45°角，施工技術不嫻熟。

3、 The installer is not a carpenter, can not cut 45 ° angle, and is not skilled in construction technology.

為了電梯門套在安裝時出現以上狀況，我們建議客戶在收到電梯門套貨物后，及時檢查尺寸是否正確標準，有沒有錯發漏發的現象，即使和廠家進行溝通確認。在電梯門套安裝過程中選擇真的木工師傅來施工，確認好尺寸后再進行切割，并且在安裝電梯門套前，先將凹凸不平的墻面用砂漿水泥找平。

In order to ensure the above conditions during the installation of the elevator door pocket, we recommend that the customer, after receiving the goods of the elevator door pocket, promptly check whether the dimensions are correct and standard, and whether there is any mistake or omission, even if they communicate with the manufacturer for confirmation. During the installation of elevator door pocket, a real carpenter shall be selected for construction, and the cutting shall be carried out after the size is confirmed. Before the installation of elevator door pocket, the uneven wall surface shall be leveled with mortar cement.

安裝前，我們建議工人需要做好電梯洞口清理好，并要在電梯洞口彈出標線。放好標準塊后，應從中到邊、從后依次放好，用尺找平。電梯門套截面尺寸需要事先裁剪好，為了避免后期出現麻煩，前期的準備工作要做好，這樣才能為電梯門套的裝飾效果打好基礎。

Before installation, we suggest that the workers should clean the elevator opening and mark the elevator opening. After placing the standard block, place it from the middle to the side and from the back, and level it with a ruler. The section size of the elevator door pocket needs to be cut in advance. In order to avoid trouble in the later stage, the preparatory work should be done well in the early stage, so as to lay a good foundation for the decorative effect of the elevator door pocket.

本文的精彩內容由電梯不銹鋼門套提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入:http://m.aplingxu.com我們有專門的客服為您解答問題

The wonderful content of this article is provided by the knowledge of elevator stainless steel door pocket. There are many wonderful content on this website. You can click to enter more content: http://m.aplingxu.com We have special customer service to answer your questions